Cervical Polyps & Plain Yogurt

instructions for a children's apron for turning

So, I habs promised, here comes the Instructions! :-)

you need are two different substances, the amount depends on how big you want to sew the skirt, plus a further material for the carrier or simply bias tape. As materials are all cotton fabrics, but also oil-cloth, if it is to be washable.

first need to take your measurement. For the upper part, we need a trapezoidal piece of cloth. The dimensions you determined by your child when you measure the length between shoulder and belly button, which is the height of the blank.

Then you measure once a belly to belly button level to about the waist (half waist circumference), which is the lower side of the trapeze. And then again up from armpit to armpit, which is upper side of the trapeze. To taste You can also make the upper side is slightly shorter.

So, now stands on the trapezoid pattern paper or whatever you use for it. ;-)

Now the "Rock", ie the lower part of the apron. I sew the skirts with one or two small darts, then the upper side of the front part be two inches longer than the lower edge of the upper. If you want to sew without the darts, then it must be the top side as long as the lower edge of the upper.
the skirt I draw simply "free hand". For Now fold your paper so that the apron is also symmetric. For girls you can, the oblique side quietly with a larger angle draw

for guys you can also, for example draw as

Then you entrust your pattern on the material. Remember the seam allowances!

cut everything. If you want to make darts at the base, your two points you marked with two lines (distance 1 cm) at the same distance from the center. Increase the distance to Center select narrower than the outside, the length is a matter of taste. transferred

All now on the other side of the apron. This simply put both arms over each other and transmit distance / length.

Who sewn with darts, it must now first stitch. , As follows: Fold the bottom part so that both lines of a fold are superimposed, sew up the end of the lines must in the end, back once more sew! Repeat with the other fold. Then press the two folds to the center.

The top right sides of the base plug (long side of the upper part of the upper side the lower part) and sew. Weld seam open.
repeat the whole thing with the cut parts for the other side of the skirt.

Now come the Bänder.Dafür there is now again in different ways, I shall now times can with bias band for about one but take any material and sew it in simple bands: simple per carrier / band mirror two pieces of cloth (important if eg a slope at the end would have) cut each other, right sides together sew, turn, topstitch to taste. Here, however, with bias tape, which is the fastest ...

desired length (remember, it should perhaps be a loop tied off!) Cut twice and four times. Then double it up and sew close to edge together. It started at the open side and end.

should end you have is four long strips.

Now it is a bit tricky. You must determine the correct position of the bands, so that the band later also runs parallel to the belly and is sewn at an angle. This is difficult because the edge of the skirt is so inclined.

The trick is, in effect, try it. Sets the tape again and again at different angles, then so it folds out, as would be held with the seam and see if the band then just at the middle seam of the skirt runs. Sounds difficult? After a few attempts have Hers out and the second skirt cuts a lot easier! Basically, the fold of the strip parallel to the still run to sewing seams, then it fits! :-) Stuck

Quick!

The support for the neck at the top of the trapezoid are stuck too. The shown variant results easily to outside makers in the manufacture aprons, you could also just be stuck in the other angle, they show the inside (may better fit), or they just simply sew.

In my version must support some work inside, so you can not be sewn by mistake.

Now insert the second part of the skirt, right on the first part and sew all around. Make sure that the "belly seams" of front and rear just another lie! At the lower end of a shift opening.

about the best approaches to support twice sew, so they are stable.

contact then, stitching the seams and stitch all around close to edge, thereby closing the opening turn. DONE!

Have fun! I would explicitly states that this guide can be used indefinitely for personal use, you can also sell individual pieces of it much. But please be so kind, before you goes into mass production, why not ask to politely! ;-)